Dometic ProHeat X30 Coolant Pump Assembly
The Dometic ProHeat 149460K Coolant Pump Assembly is the factory replacement coolant circulation pump used in compatible ProHeat X30 coolant heaters.
The X30 relies on its integrated coolant pump to circulate heated coolant through the engine, equipment, or auxiliary heating circuit. Proper coolant circulation is essential for transferring heat away from the heater and throughout the connected cooling system.
The 149460K assembly provides the factory pump along with the related hose and clamping components identified by ProHeat for installation.
Key Features
- Genuine Dometic ProHeat replacement assembly
- Factory part number 149460K
- Designed for compatible ProHeat X30 coolant heaters
- Complete coolant pump assembly
- Supports proper coolant circulation through the heating system
- Includes coolant hose and associated clamps
- Factory replacement for service and repair
- Rebuild kit available separately for serviceable pump components
What Is Included
According to the official ProHeat X30 parts catalog, the 149460K Coolant Pump Assembly includes the pump along with the related installation components shown in the factory coolant pump assembly.
Included components are:
- 149460K – X30 Coolant Pump Assembly
- 149076K – #28 Stainless Steel Gear Clamp
- 149372K – Coolant Hose Clamps, 2-pack
- 149034K – 3/4 × 2.5 in Coolant Hose
These components are listed together as part of the complete X30 coolant pump assembly.
Compatibility
Manufacturer: Dometic ProHeat
ProHeat Part Number: 149460K
BTRAC Part Number: PH-149460K
Product Type: Coolant Pump Assembly
Heater Family: ProHeat X30
Application: Coolant circulation / replacement pump
The current ProHeat X30 parts catalog lists 149460K in the coolant pump assembly section for single-fuel-line X30 models.
Important Fitment Note
ProHeat maintains separate parts catalogs for earlier dual-fuel-line X30 heaters and later single-fuel-line models.
The current single-fuel-line catalog applies to X30 heaters with serial number:
X3H18017001 and above
For earlier X30 heaters, verify the existing coolant pump part number and heater serial number before ordering. ProHeat maintains both current and legacy X30 documentation for service verification.
How the Coolant Pump Functions
The ProHeat X30 is designed as an auxiliary coolant heater with an integrated circulation pump.
During operation, the coolant pump moves heated coolant through the connected system. Depending on the application, this can help:
- Preheat an engine before startup
- Circulate heat through an engine cooling loop
- Supply heated coolant to a cab or passenger heat exchanger
- Warm equipment or auxiliary systems connected to the coolant circuit
- Maintain more consistent system temperatures in cold conditions
Dometic identifies the integrated coolant pump as a standard feature of the X30 platform.
Serviceable Pump Design
ProHeat offers a separate 865893K Coolant Pump Rebuild Kit for servicing internal pump components when complete pump replacement is not required.
The rebuild kit includes:
- Separator cup
- Thrust washer
- Impeller magnet
- Impeller shaft
- O-ring
- Pump body
- Fasteners
- Two coolant hose clamps
- Pump rebuild instructions
The 972726K Coolant Pump Drive Cup with set screw is also available separately.
This gives technicians the option of rebuilding certain pump components or replacing the complete 149460K assembly, depending on the condition of the existing unit.
Installation Notes
Coolant-system service should be performed according to the applicable ProHeat X30 installation and service procedures.
Before installation:
- Confirm the heater is a compatible ProHeat X30
- Verify the existing pump part number
- Confirm the heater serial number when servicing an older X30
- Allow the heater and coolant system to cool before service
- Disconnect electrical power where required
- Inspect surrounding coolant hoses for cracks, swelling, or damage
- Check clamps and fittings before reassembly
- Refill the system with the correct coolant mixture
- Remove trapped air from the coolant loop after service
- Check all connections for coolant leaks
- Confirm proper coolant circulation before returning the heater to service
Adequate coolant flow is essential to proper X30 operation and heat transfer.
Product Specifications
- BTRAC SKU: PH-149460K
- Manufacturer: Dometic ProHeat
- Manufacturer Part Number: 149460K
- Product Type: Coolant Pump Assembly
- Compatible Heater: ProHeat X30
- Coolant Hose Size: 3/4 in
- Included Hose Length: 2.5 in
- Includes Stainless Gear Clamp: Yes
- Includes Coolant Hose Clamps: Yes
- Application: Replacement / service component
Related Parts
- 865893K – X30 Coolant Pump Rebuild Kit
- 972726K – Coolant Pump Drive Cup with Set Screw
- 149076K – #28 Stainless Steel Gear Clamp
- 149372K – Coolant Hose Clamp, 2-Pack
- 149034K – 3/4 × 2.5 in Coolant Hose




Reviews
There are no reviews yet.