PH-940326K – Dometic ProHeat CP1800 12V Coolant Pump

$458.23

The Dometic ProHeat 940326K CP1800 Coolant Pump is a genuine 12V replacement circulation pump for compatible ProHeat X45 and X45 Plus coolant heaters. The replacement kit includes the pump, mounting … Read more

22 in stock

SKU: PH-940326K Category:

Dometic ProHeat CP1800 12V Coolant Pump

The Dometic ProHeat 940326K CP1800 Coolant Pump is the factory 12-volt replacement circulation pump used in ProHeat X45 and X45 Plus diesel-fired coolant heaters.

The coolant pump moves heated coolant through the connected engine and auxiliary heating circuit. Proper circulation allows the ProHeat system to transfer heat from the heater to the engine, cab heater core, or other connected coolant-based heating components.

ProHeat identifies 940326K as the 12V coolant pump, with 942820K serving as the corresponding 24V version.

Key Features

  • Genuine Dometic ProHeat replacement component
  • Factory part number 940326K
  • CP1800 centrifugal coolant pump
  • 12V electrical system
  • Designed for ProHeat X45 and X45 Plus heaters
  • Complete replacement kit with mounting and hose hardware
  • Supports engine preheating and auxiliary coolant circulation
  • Rebuild components available separately
  • Factory-documented installation procedure

Compatibility

  • Manufacturer: Dometic ProHeat
  • ProHeat Part Number: 940326K
  • BTRAC Part Number: PH-940326K
  • Pump Model: CP1800
  • Product Type: Coolant Circulation Pump
  • Voltage: 12V
  • Compatible Heater: ProHeat X45
  • Compatible Heater: ProHeat X45 Plus

ProHeat lists the 940326K 12V coolant pump in the X45 Plus air compressor, fuel pump, and coolant pump assembly. The same factory documentation lists 942820K for 24V systems.

CP1800 Pump Design

ProHeat factory service documentation identifies 940326K as the CP1800-12V coolant pump.

The CP1800 is a centrifugal circulation pump designed to move coolant through the ProHeat heating circuit during heater operation.

Depending on the vehicle or equipment installation, coolant circulation can support:

  • Engine preheating
  • Easier cold-weather starting
  • Reduced cold-start wear
  • Auxiliary cab or passenger heat
  • Supplemental heat while operating
  • More even coolant temperatures throughout the heating circuit

Replacement Kit Includes

The official ProHeat installation instructions for the 940326K / 942820K X45 Coolant Pump Kit specify the following new components for reassembly:

  • 1 × Coolant Pump
  • 1 × J-Bracket
  • 2 × #10 Hose Clamps
  • 1 × #32 Hose Clamp
  • 3 in × 3/4 in ID Coolant Hose
  • 1 × 11.5 in Cable Tie

The factory procedure reuses the existing heater elbow fitting and mounting bolt.

12V Application

The 940326K is specifically designed for 12V ProHeat applications.

For 24V X45 and X45 Plus systems, use:

942820K – CP1800 24V Coolant Pump

Always verify the vehicle voltage and existing pump part number before ordering.

Serviceable Pump Design

ProHeat also offers the 865893K Coolant Pump Rebuild Kit for applications where rebuilding the existing pump is appropriate rather than replacing the complete assembly.

Factory X45 Plus documentation identifies the rebuild kit with service components including:

  • Separator cup
  • Thrust washer
  • Impeller magnet
  • Impeller shaft
  • O-ring
  • Pump body
  • Fasteners
  • Coolant hose clamps
  • Pump rebuild instructions

The 972726K coolant pump drive cup with set screw is also available separately.

Installation Notes

ProHeat’s factory replacement procedure includes several important installation requirements:

  • Allow the coolant system to cool completely before service
  • Disconnect electrical power from the heater
  • Isolate the heater coolant circuit before removing the pump
  • Replace the supplied coolant hose and clamps during installation
  • Inspect surrounding hoses for cracks or damage
  • Make sure the heater and pump are filled with coolant before operation
  • Check coolant level after installation
  • Inspect all connections for leaks
  • Operate the heater for at least two cycles after replacement

The CP1800 does not self-prime and must not be operated dry.

ProHeat also specifies installation of the supplied cable tie to secure the electrical connector. This helps prevent pump wiring from chafing or breaking during operation.


Product Specifications

  • BTRAC SKU: PH-940326K
  • Manufacturer: Dometic ProHeat
  • Manufacturer Part Number: 940326K
  • Pump Model: CP1800
  • Product Type: Centrifugal Coolant Circulation Pump
  • Voltage: 12V
  • Compatible Heater: ProHeat X45
  • Compatible Heater: ProHeat X45 Plus
  • Coolant Hose ID: 3/4 in
  • Replacement Hose Length: 3 in
  • J-Bracket Included: Yes
  • #10 Hose Clamps Included: 2
  • #32 Hose Clamp Included: 1
  • Cable Tie Included: Yes
  • Application: Replacement / service component

Related ProHeat Parts

  • PH-942820K – CP1800 24V Coolant Pump
  • 865893K – Coolant Pump Rebuild Kit
  • 972726K – Coolant Pump Drive Cup with Set Screw
  • 962823K – #10 Silicon Hose Clamp
Weight 3.3261 lbs
Dimensions 10 × 5 × 4 in

Reviews

There are no reviews yet.

Be the first to review “PH-940326K – Dometic ProHeat CP1800 12V Coolant Pump”

Your email address will not be published. Required fields are marked *