PH-844222K – Dometic ProHeat X45/X45 Plus & XL900 Combustion Tube

$261.25

The Dometic ProHeat 844222K Combustion Tube is a genuine replacement combustion component for ProHeat X45, X45 Plus, and XL900 heaters. Designed for both 12V and 24V heater configurations, the combustion … Read more

20 in stock (can be backordered)

SKU: PH-844222K Category:

Dometic ProHeat Combustion Tube

The Dometic ProHeat 844222K Combustion Tube is the factory replacement combustion tube used in ProHeat X45, X45 Plus, and XL900 diesel-fired coolant heaters.

Located inside the heater’s heat exchanger assembly, the combustion tube is directly involved in the heater’s combustion process. During startup, the fuel nozzle produces a fine air/fuel mist and the ignition electrode sparks to the combustion tube to ignite the mixture.

A damaged, heavily contaminated, or deteriorated combustion tube can affect proper heater operation and should be inspected whenever the combustion chamber or heat exchanger is serviced.

Key Features

  • Genuine Dometic ProHeat replacement component
  • Factory part number 844222K
  • Fits ProHeat X45
  • Fits ProHeat X45 Plus
  • Fits ProHeat XL900 Mark I
  • Fits ProHeat XL900 Mark II
  • Compatible with both 12V and 24V heater configurations
  • Installs inside the heat exchanger assembly
  • Integral component of the heater combustion system
  • Factory replacement for service and repair

Compatibility

  • Manufacturer: Dometic ProHeat
  • ProHeat Part Number: 844222K
  • BTRAC Part Number: PH-844222K
  • Product Type: Combustion Tube
  • ProHeat X45: Yes
  • ProHeat X45 Plus: Yes
  • ProHeat XL900 Mark I: Yes
  • ProHeat XL900 Mark II: Yes
  • 12V Applications: Yes
  • 24V Applications: Yes

The same 844222K combustion tube is used across both 12V and 24V versions of the applicable heaters.

Important XL-Series Fitment Note

The 844222K is the combustion tube for ProHeat XL900 heaters.

It should not be confused with:

844200 – ProHeat XL1500 Combustion Tube

Verify the heater model before ordering for legacy XL-Series applications.

Role in the Combustion System

The ProHeat X45 fuel system uses compressed air and fuel to create a fine mist through the heater nozzle.

During the ignition sequence:

  1. Fuel and compressed air are supplied to the nozzle.
  2. The nozzle creates a finely atomized air/fuel mixture.
  3. The mixture enters the combustion chamber.
  4. The ignition electrode produces a spark to the combustion tube.
  5. The air/fuel mixture ignites and produces heat.
  6. Heat is transferred through the surrounding heat exchanger to the circulating coolant.

Because the combustion tube operates directly within this high-temperature environment, deposits and heat-related wear should be evaluated during major heater service.

Heat Exchanger Service

ProHeat recommends inspecting and cleaning the heat exchanger to maintain proper heat transfer.

The combustion tube must be removed to access the internal heat exchanger fins.

During heat exchanger service:

  • Remove the fan-end assembly
  • Remove the combustion tube
  • Inspect the combustion area for deposits
  • Clean combustion deposits from the heat exchanger fins
  • Inspect the exhaust system for restriction
  • Check the combustion tube for damage or deterioration
  • Reassemble according to ProHeat service procedures

ProHeat recommends using a wire brush and vacuum to remove deposits from the heat exchanger rather than washing the internal components.

Installation Notes

When installing the combustion tube:

  • Shut the heater down completely
  • Allow the heater and exhaust system to cool
  • Disconnect electrical power before service
  • Inspect the combustion chamber and heat exchanger
  • Inspect the ignition electrode and surrounding components
  • Apply anti-seize compound to the combustion tube cap screws
  • Tighten the four combustion tube screws evenly
  • Confirm proper heater operation after reassembly

Factory Torque Specification

ProHeat specifies:

Combustion Tube Cap Screws:
25 ± 3 in-lb (2.8 ± 0.3 Nm)

Apply anti-seize to the cap screws before installation.

Related ProHeat Components

The combustion tube is located within the heat exchanger assembly alongside components such as:

  • 934522K – Heat Exchanger with Elbows
  • 933525K – X45/X45 Plus Igniter with Gasket
  • 913526K – Ignition Coil
  • 930523K – Ignition Lead
  • 954329K – Flame Sensor
  • 845028K – 10 in Straight Exhaust Pipe
  • 980521K – 24 in 90° Exhaust Pipe
  • 909521K – Exhaust Pipe Clamp

These components are sold separately unless otherwise specified.


Product Specifications

  • BTRAC SKU: PH-844222K
  • Manufacturer: Dometic ProHeat
  • Manufacturer Part Number: 844222K
  • Product Type: Combustion Tube
  • Compatible Heater: ProHeat X45
  • Compatible Heater: ProHeat X45 Plus
  • Compatible Legacy Heater: ProHeat XL900 Mark I
  • Compatible Legacy Heater: ProHeat XL900 Mark II
  • System Voltage Compatibility: 12V / 24V
  • System: Combustion / heat exchanger
  • Application: Replacement / service component
  • Installation Torque: 25 ± 3 in-lb (2.8 ± 0.3 Nm)
Weight 2.3565 lbs
Dimensions 13 × 8 × 7 in

Reviews

There are no reviews yet.

Be the first to review “PH-844222K – Dometic ProHeat X45/X45 Plus & XL900 Combustion Tube”

Your email address will not be published. Required fields are marked *