Dometic ProHeat X45 12V Blower Assembly
The Dometic ProHeat 980212K Blower Assembly is the factory 12-volt replacement blower used in ProHeat X45 and X45 Plus diesel-fired coolant heaters.
The blower supplies the airflow required for proper heater combustion. The ProHeat control system monitors blower operation and speed to make sure sufficient combustion air is available while the heater is running.
ProHeat supplies 980212K as a complete assembly with the blower gasket and fan blade included, reducing the need to transfer those components from the existing blower.
Key Features
- Genuine Dometic ProHeat replacement component
- Factory part number 980212K
- Designed for ProHeat X45
- Designed for ProHeat X45 Plus
- 12V blower assembly
- Supplies combustion airflow to the heater
- Includes blower gasket
- Includes fan blade
- Blower operation is monitored by the ProHeat control system
- Direct replacement/service component
What Is Included
The official ProHeat X45 Plus parts catalog identifies 980212K as:
Blower, 12V c/w Gasket & Fan Blade
The assembly therefore includes:
- 12V blower motor assembly
- Blower gasket
- Fan blade
The factory catalog also identifies these components separately for service:
- 964424K – Blower Gasket
- 900316K – Fan Blade with Glue
When purchasing the complete 980212K blower assembly, a gasket and fan blade are already included.
Compatibility
- Manufacturer: Dometic ProHeat
- ProHeat Part Number: 980212K
- BTRAC Part Number: PH-980212K
- Product Type: Blower Assembly
- Voltage: 12V
- Compatible Heater: ProHeat X45
- Compatible Heater: ProHeat X45 Plus
- System: Combustion air / fan end
The same 980212K blower is documented in the factory parts catalogs for both X45 and X45 Plus heaters.
Need the 24V Version?
For 24V X45 and X45 Plus heaters, use:
PH-980224K – Dometic ProHeat X45/X45 Plus 24V Blower Assembly
ProHeat lists the two versions together:
- 980212K – 12V Blower
- 980224K – 24V Blower
Blower Monitoring and Diagnostics
The X45 control system monitors blower operation electronically.
The PCM measures blower speed and can generate a fault if blower RPM falls below the level required to maintain sufficient combustion air.
On the X45 diagnostic system, the blower is identified as:
Diagnostic Code 12 – Blower
A blower-related fault can result from conditions such as:
- Failed blower motor
- Open electrical circuit
- Short circuit
- Damaged wiring or connector
- Insufficient blower speed
- Fan blade rubbing against the housing
- Fan blade slipping on the motor shaft
ProHeat recommends diagnosing the wiring and blower before replacing the control module.
Electrical Specification
The ProHeat X45 service manual provides the following normal current range for the 12V blower:
0.75–1.5 amps at 12 volts
This value can be useful when diagnosing blower operation before replacement.
Combustion Chamber Inspection
ProHeat specifically recommends inspecting the combustion chamber if the blower has failed.
A blower problem can affect combustion airflow and contribute to carbon accumulation. When replacing a failed blower, inspect the combustion chamber for carbon buildup and clean it as necessary before returning the heater to service.
Blower Inlet Inspection
The surrounding fan-end assembly also includes the:
964321K – Blower Inlet Screen Kit
When servicing the blower, inspect the inlet screen and surrounding air path for dirt, debris, or restrictions that could reduce airflow. The blower inlet screen is sold separately.
Installation Notes
Before replacing the blower:
- Shut the heater down completely
- Allow the heater to complete its cool-down cycle
- Disconnect vehicle batteries before electrical service
- Inspect the blower connector and wiring
- Inspect the blower inlet screen for contamination
- Inspect the combustion chamber if the existing blower failed
- Confirm the fan blade rotates freely after installation
- Reinstall all protective covers before operating the heater
- Test heater startup and blower operation after installation
ProHeat cautions that moving and electrical components can present a hazard and directs technicians to disconnect battery power before heater service.
Product Specifications
- BTRAC SKU: PH-980212K
- Manufacturer: Dometic ProHeat
- Manufacturer Part Number: 980212K
- Product Type: Blower Assembly
- Voltage: 12V
- Compatible Heater: ProHeat X45
- Compatible Heater: ProHeat X45 Plus
- System: Combustion Air / Fan End
- Normal Current Draw: 0.75–1.5A @ 12V
- Fan Blade Included: Yes
- Blower Gasket Included: Yes
- Application: Replacement / service component
Related ProHeat Parts
- PH-980224K – X45/X45 Plus 24V Blower Assembly
- PH-964424K – Blower Gasket
- PH-900316K – Fan Blade with Glue
- PH-964321K – Blower Inlet Screen Kit
- PH-954329K – Flame Sensor
- PH-951126K – Fuel Regulator
Reviews
There are no reviews yet.